我公司中型高压电动机生产设备先进,技术领先,管理一流,拥有各种设备100余台套,其中有引进ABB技术同时也是中型高压电机制造的关键设备——无容剂漆真空整浸缘处理设备(简称VPI),以及国内目前最先进的电机机座加工中心,设备、技术堪称国内一流。
一、 概况 Y、YR系列、YKS、YRKS系列和YKK、YRKK系列高压三相异步电动机(中心高355-630)毫米,是按照引进瑞士ABB公司高压三相异步电动 机设计制造技术,结合40多年长期稳定的高压三相异步电动机系列的设计制造经验而建立的优化系列,是JS、JSQ、JR和JRQ老系列产品的更新换代产 品。本系列产品用料考究,制造精良,且有力能指标高,噪声及振动小,可靠性高,使用安装维修方便等优点。本系列电动机的功率等级、安装尺寸、电气性能均符 合国家标准GB755《旋转电机基本技术要求》,国际电工委员会IEC标准和机械电子工业部企业标准JB/DQ3134,JB/DQ3135,JB /DQ3436和JB/DQ3437。本系列电动机各部分机械尺寸、公差符合国家标准GB1800-1804和国际标准化委员会ISO标准。本系列电动机 外壳防护等级根据GB4942-1和IEC34-5《电机外壳防护分级》有IP23和IP44两种,防滴式IP23电动机也可按用户提出的要求制成管道通 风式IPR44。如果用户需要其他防护等级如IP54及IP24等可另行协商。本系列电动机的冷却方法根据GB1993和IEC34-6《电机冷却方法》 的标准,有IC01、IC0161和ICW37A81等三种。如果用户要求其他冷却方法可另行协商。本系列电动机基本安装方式为卧式带底脚(IMB3)结 构,符合GB997和IEC34-7《电机结构及安装形式代号》的规定。
1. General De
本系列电动机按照转子类型、防护等级及冷却方式可分为以下六个系列:
型号 |
防护等级 |
冷却方式 |
转子类型 |
|
鼠笼转子型 |
绕线转子型 |
|||
防滴式 |
IP23 |
IC01 |
Y系列 |
YR系列 |
空-水冷却封闭式(TEWAC) |
IP44 |
ICW37A81 |
YKS系列 |
YRKS系列 |
空-空冷却封闭式(TEAAC) |
IP44 |
IC0161 |
YKK系列 |
YRKK系列 |
According to the type of rotors, enclosure protection degree and type cooling,
The motors of these series are classified as follows:
Type |
Protection Degree |
Type of Cooling |
Type of Rotor |
|
Squirrel Cage |
Wound Rotor |
|||
Drip-proof |
IP23 |
IC01 |
Y Series |
YR Series |
Enclosed Air-Water Cooling(TEWAC) |
IP44 |
ICW37A81 |
YKS Series |
YRKS Series |
Enclosed Air-Air Cooling(TEAAC) |
IP44 |
IC0161 |
YKK Series |
YRKK Series |
* * * * * * *
订货注意事项
Customer Attention for Placing an Order
请在订货时注明以下参数
1.电机型号(Y5002-4) 2.额定功率(千瓦)(630千瓦) 3.额定电压(伏)(10000伏) 4.极数(4) 5.额定频率(赫)(50赫) 6.防护等级(IP23) 7.冷却方式(IC01) 8.安装方式(IMB3) 旋转方向(顺时针转向)(面对电机轴伸端看) 10.出线盒位置(电机右侧)(面对电机轴伸端看) 11.环境条件(海拔≤1000米 -10~+40ºC) 另请注意: 1.其他特殊要求,需另订技术协议后方可签订订货合同. 2.如订货时无特殊说明,面对电机轴伸端看,电机为顺时针方向旋转,出线盒在右侧. 3.随着技术的进步和有关国内外标准的修改,样本内技术参数有所变动,请以咨询后为准.
|
The following should be specified when placing an order:
1.type of motor such as(Y5002-4) 2.rated output(KW)(630KW) 3.rated voltage(V)(10000V) 4.No.of poles(4) 5.rated frequency(HZ)(50HZ) 6.degree of enclosur protection(IP23) 7.type of cooling(IC01) 8.type of mounting(IMB3) 9.directin ofrotation(clockwise,viewling form shaft extension side) 10.location of lead ox (at right side of motor ,viewing from shaft extension side) 11.enviromental condition (see level≤1000m, -10to+40ºC) 1.If there are special requirementrs,a technical agreement should be entered into before signing the order contract. 2.If on special requirement is raised when placing and order, the motor willrun in clckwise direction and the lead box will be at the right side of the motor viewinig from the shaft extension side. 3.The technical deta are subject to change withut notice because of technical progres and the revising of domestic and international standardx. |